What should not be done when operating a forklift?

Avoid standing or walking under a load, lifting mechanism, or forklift attachment, as loads can fall off on anyone positioned below it. Keep hands and feet clear away from the forklift mast, as a moving mast can cause serious injury.

What can you not do with a forklift?

Forklift operators should never:

  • Raise or lower loads while the forklift is moving and especially not while turning because it makes the forklift very unstable. …
  • Allow anyone to stand underneath or right next to raised forks. …
  • Carry a load with only one fork as it stresses the carriage.

What should you do before operating a forklift?

You need to check any automatic cutoff switches or sensors to make sure they work as they should. Do your windshield wipers (if installed) and seatbelt work properly? Lights and signals should also be checked to make sure they are in good order and that they do not need to be replaced before you hit the floor running.

IT IS IMPORTANT:  What rules should be followed while hoisting our national flag?

What is the correct behavior when operating a forklift?

Normally the operator should travel straight up and down Do not attempt to turn around on grades or ramps. Keep loads elevated and upslope, not pointed downslope. On grades, tilt the load back and raise it only as far as needed to clear the road surface. Do not raise or lower the forkswhile the forklift is moving.

What are the hazards of forklift?

10 Forklift Hazards & Solutions

  • 1) Horseplay & Improper Use. …
  • 2) Pedestrians. …
  • 3) Unsecured Loads. …
  • 4) Lack of Maintenance. …
  • 5) Floor Conditions. …
  • 6) Docks. …
  • 8) Over Capacity Loads. …
  • 9) Overhead Obstructions.

What are the 3 pedals on a forklift for?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

What is the first step to ensure safe operation of your pit at the start of every shift?

PITs must be inspected at the beginning of each shift to ensure they are safe to operate . These inspections may be performed by authorized PIT operators as long as they are trained on how to properly inspect the PIT .

What is the first thing an operator should check on a forklift?

Forklift Visual Pre-Start Checklist

Check your forklift structure for any dents, broken parts or cracks. Check that the floor of the warehouse is clear of objects that may get in the way. You should also check overhead to make sure there is no obstructions that could cause an accident.

IT IS IMPORTANT:  How do you recondition a forklift battery?

What are 3 fluid levels that need to be checked before using the forklift?

Check of liquid Levels:

  • Hydraulic fluid.
  • Brake fluid.
  • Engine oil coolant.
  • Battery.
  • Fuel.

What are seven hazards in a forklift operating area?

In this week’s post we briefly describe ten common forklift hazards and how they can be mitigated to improve safety.

  • Improper Operation and Use. …
  • Load Hazards. …
  • Insufficient or Incorrect Maintenance. …
  • Pedestrians. …
  • Floor Conditions. …
  • Overhead Obstructions. …
  • Unit Refueling. …
  • Attachments.

What are the controls on a forklift?

There are three forklift directional controls: park, drive, and reverse. Directional controls can be mounted to a lift’s steering column. Or, they may be placed in a position where an operator controls them with their foot.

What are the 4 main causes of forklift injuries?

Common Forklift Accidents To Avoid

  • A Poorly Trained Operator/Driver. …
  • Faulty Equipment. …
  • Speeding. …
  • Tipping of a Pallet or Damaging Racking. …
  • Toppling Over. …
  • Driving the Vehicle With An Elevated Load. …
  • Insufficient Marking. …
  • Improper Turning.

What are the hazards in a warehouse?

The 7 Most Common Warehouse Hazards and How to Reduce Your Risk

  • Physical Strain.
  • Moving Machinery.
  • Loading and Unloading.
  • Falling Objects.
  • Exposure to Harmful Substances.
  • Lack of Safety Training and Knowledge.
  • Slips, Trips and Falls.

What is the most common cause of forklift accidents?

Here is a breakdown of the most common causes of forklift accidents:

  • Overworked or overstressed forklift operators.
  • Encouraging forklift operators to cut corners to get the job done more quickly.
  • Poor maintenance of forklifts.
  • Failing to replace forklifts when they are no longer safe to use.
IT IS IMPORTANT:  You asked: How does a hydraulic car lift work?