What does the overhead guard do on a forklift?

An overhead guard is designed to protect the operator from falling objects. Wear a hard hat when appropriate for additional protection. Keep hands and feet within the forklift to avoid danger of falling loads.

What is the main purpose of the overhead guard?

Use an overhead guard as protection against falling objects such as small packages, boxes, bagged material, etc., but not to withstand the impact of a falling capacity load.

What is the guard called on a forklift?

The overhead guard is a critical feature of a forklift’s safety. The overhead guard’s purpose is to help protect the operator should something fall onto the forklift cab.

What three guards are fitted to a forklift?

In the manufacturers instructions. Overhead Guard – • Protects the operator from falling objects. Load Backrest – • Protects the operator and stops the load from hitting the mast. Foot Guard – • Protects the operators feet.

IT IS IMPORTANT:  How often do you need forklift refresher training?

What is the most important safety device on a forklift?

5 most important safety devices on a forklift

  1. Brakes. Brakes are the absolute most important safety feature on any motorized vehicle. …
  2. Seatbelts. …
  3. Overhead guards. …
  4. Lights. …
  5. Horn.

When Travelling with a load on your forks you should?

Travel with forks as low as possible from the floor and tilted back (usually within 10-15 cm (4 to 6 inches) above the floor). Match speed to, load, presence of pedestrians, obstructions, and driving and workplace conditions, including slippery surfaces.

What is the stability triangle on a forklift?

What is the stability triangle? Most counterbalanced forklifts have a three-point suspension system, meaning that the truck is supported at the two front wheels and the center of the steer axle. If you imagine all three points connected into a triangle, this is the forklift’s stability triangle.

What are the controls on a forklift?

There are three forklift directional controls: park, drive, and reverse. Directional controls can be mounted to a lift’s steering column. Or, they may be placed in a position where an operator controls them with their foot.

What are the 3 major parts of a forklift?

The three major parts of a lift truck are the body (truck), overhead guard, and hydraulic lift.

How do forklift controls work?

Make sure the truck is placed squarely in front of the load. Make sure the forks are at the correct height for lifting the load. Set the direction control to neutral. Never raise or lower the forks unless the forklift is stopped and the brake is set.

IT IS IMPORTANT:  Is flag hoisted on Republic Day?

What are tiger tails used for forklift?

Tiger Tails® are used extensively by Utilities and Electrical Contractors as temporary electrical insulation, mechanical protection and visual warning of power lines and conductors.

What can be found on all lift trucks?

The three major parts of a lift truck are the body (truck), overhead guard, and hydraulic lift.

What is a load backrest on a forklift?

Load backrests play an important role in keeping your drivers safe. They prevent your forklift’s load from falling toward the driver. It features a steel grid above the forks and attaches to the sides of the forklift carriage with heavy-duty, steel framing.

What is inching on a forklift?

The purpose of the inching pedal is to disengage the transmission without having to shift the gear lever into neutral every time a lift is performed. This pedal allows you to bring the forklift to a stop or to slow it down. … This pedal allows you to adjust the rotational speed of the engine.

Why are there 3 pedals on a forklift?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. … That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

What safety guards do forklifts have?

To protect forklift operators from this potentially deadly situation most modern forklift masts are equipped with what is known as a ‘load guard’. The pallet is positioned on the tines such that one surface is flush with the load guard. This further increases the stability of the load when the mast is tilted back.

IT IS IMPORTANT:  Are forklifts manual?