Quick Answer: How do you reverse a forklift?

How do you drive a forklift in reverse?

When driving in reverse, always face the rear of the forklift, rather than twisting around. Twisting could result in a serious back injury and also means that you won’t have a constant view of your load. As you reverse, make sure that you keep looking in the direction of travel.

Do you drive a forklift with both feet?

You should have two feet and a hand or two hands and a foot in contact with the vehicle at all times. … Always keep a minimum of three vehicle distances in between any operational forklifts when driving in the same direction.

Do forklifts need reversing alarms?

There is no absolute requirement for Reversing Alarms to be fitted to fork lift trucks.

Do forklifts overturn or tip easily?

An unstable forklift can quite easily roll over or tip, with approximately one in six overturned forklifts resulting in operator death. … Cornering too fast, braking too quickly or driving on uneven ground are some of the most typical ways for a forklift to overturn.

IT IS IMPORTANT:  How much does a forklift Licence cost in South Africa?

In what situation are you most likely to need to drive a forklift in reverse?

If the load is too large to see clearly over the top of the load, move the load by driving backwards. Forklift drivers must also drive backwards when going down or up an incline.

What is inching on a forklift?

The purpose of the inching pedal is to disengage the transmission without having to shift the gear lever into neutral every time a lift is performed. This pedal allows you to bring the forklift to a stop or to slow it down. … This pedal allows you to adjust the rotational speed of the engine.

What are the 3 pedals on a forklift for?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

What should you not do while operating a forklift?

Avoid standing or walking under a load, lifting mechanism, or forklift attachment, as loads can fall off on anyone positioned below it. Keep hands and feet clear away from the forklift mast, as a moving mast can cause serious injury.

Do and don’ts for forklift?

The 5 Dos and Don’ts of Forklift Safety

  • Do Drive Responsibly. Just like driving a car on the road, you should always operate your forklift at a speed that will allow you to stop safely. …
  • Don’t Go Over Your Forklift’s Load Capacity. …
  • Do Be Aware of Pedestrians. …
  • Don’t Skimp on Training. …
  • Do Maintain Your Forklift.
IT IS IMPORTANT:  How far can a 60 ton crane reach?

Why are there 2 brakes on a forklift?

To begin with, every forklift comes equipped with an accelerator and a brake pedal. … That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.

How do you reverse a delivery van?

Reverse slowly, use the mirrors and check both sides. Look back and continue to look back whilst moving in reverse. Reversing vehicles have no right of way. If a vehicle approaches from behind, remain stationary and GIVE WAY until it passes.

Are reversing alarms a legal requirement?

That these automatic alarms are not mandatory on vehicles means that the law do not automatically recognise that a hazard exists – and if it doesn’t then use of an alarm when driving in a built up area between the hours of 11.30 pm and 7.00 am is an offense!

Should forklifts have mirrors?

Mirrors are such a mandatory requirement just like the reverse alarm and seat belts. It should be a standard issue by the manufacturer. If you don’t have mirrors on your forklift, you can opt to have them installed on the truck.