How much can a John Deere 1025R pull?

This means the 25 horsepower 1025R can handle a towed load of approximately 3,100 lbs and the 3025D can handle nearly 5,200 lbs. The 1025R is rated to lift 681 lbs on the rear three-point hitch and the 3025D can handle 1,670 lbs on the rear.

How much weight can a John Deere tractor pull?

MAXIMUM OPERATING WEIGHT SHOULD NOT EXCEED 50,000 LB. (22,680 KG). IMPORTANT: Maximum transport speeds may be limited to the speed where steering control and vehicle stability can be maintained.

Track frame weights.

Track frame support (front) 140 lb. (64 kg)
Quik-Tatch weights (each) 100 lb. (45 kg)

How much weight can a 1025R bucket lift?

Super Moderator. Depending on configuration, the 1025R/H120 combo is rated for either 836lbs or 955lbs plus the bucket weight.

How many hours does 1025R last?

10 hours and not a single issue yet. Except there’s not enough time in the day.

How much weight can a subcompact tractor pull?

For instance, a small tractor can have a relatively low towing capacity of about 2,300 to 2,500 lbs.

IT IS IMPORTANT:  Can I put car motor oil in a lawn mower?

How much can a tractor pull?

Today’s tractors can achieve theoretical speeds over 200 km/h (125 mph). Today’s drags (sled) use a complex system of gears to move weights up to 29,000 kilograms (65,000 lb). Upon starting, all the weights are over the drag’s (sled) rear axles, to give an effective weight of the drag plus zero.

How much can a John Deere 1025r loader lift?

Everything I’ve read says the 1025r & H120 has a lift capacity of 836lbs. So I was rather surprised when I put in 10 JD Quick-Tatch (R127764) weights in the bucket and the loader operated (curl, rise, lower, dump) just fine (minus the DBS of course) at idle. So that is 1040lbs, 20% above the rated capacity.

How fast can a John Deere 1025r go?

4.5 MPH in A range and 9 MPH in B range in spite of the much bigger tires.

How much can a 1025R lift with forks?

These ultra lightweight pallet forks are the best option for the John Deere 1025r subcompact tractor. You can buy these from Good Works Tractors! Equipped with 36″ tines, these pallet forks weigh only 190 pounds and will outlift the capacity of your loader at 900 pounds at a 21″ load center!

How much can a John Deere 2025R lift?

Key Specs

Engine power (gross) 17.8 kW 23.9 hp SAE J1995 rated power
Implement hydraulics 13.25 L/min 3.5 gpm
Hitch type Limited Category 1
Lift capacity, 24-in. behind link arms 400 kg 882 lb
Standard transmission; forward/reverse Hydrostatic – 2 range

How big is the bucket on a John Deere 1025R?

John Deere 1025R Attachments

IT IS IMPORTANT:  Are Kubota tractors made in Canada?
John Deere H120 Loader
Loader weight: 541 lbs 245 kg
Lift to 1.5m (at pin): 955 lbs 433 kg
Lift to 1.5m (at 500mm): 686 lbs 311 kg
Bucket width: 49 inches 124 cm

Is 1000 hours a lot on a tractor?

Tractors that have been well maintained average about 8,000 to 10,000 engine hours before requiring more unscheduled maintenance. Compact tractors with diesel engines average 6,000 to 8,000 hours, while gas engine tractors average 6,000 to 8,000 as well.

What is high hours on a backhoe?

The CE Lifecycle Study indicates that’s 8,500 hours for backhoe-loader engines, and 10,000 hours for engines in big ADTs.

What is too many hours on a tractor?

However, other aspects of the machine, like the transmission, clutches, hydraulics, and more may need to be replaced to keep the tractor in good running order. A general rule of thumb is that 2,000 to 2,500 hours is well broken-in while anything above 35,000 hours is considered high.